images 15454 m6 dc40 upright

M6 fan tray assemblies. Use copper conductors only. When the chassis is installed in the middle position, in an ETSI rack, the cabinet doors must be kept open if present. With all connections to the Cisco ONS M6 located on the front, this platform is ideal for cabinet installations and ETSI front connection requirements, making it truly global in its appeal. The retention feature maintains the door in the horizontal position for line card insertion see the following figure. IS ANSI inch cabinet. Ensure that the host is connected to earth ground during normal use. Table 4. Specifically designed for the Cisco ONS M6 MSTP are control cards that consolidate the functions of the shelf processor, optical service channel OSC termination, multi-shelf switch, and external alarm contacts into just one card.

  • Cisco ONS M6 Multiservice Transport Platform Data Sheet Cisco

  • Cisco DC Power Supply - Power supply - Watt - for ONS M6 M6-DC The ONS M6 requires mm (inches) minimum of vertical Remove the M6-DC20 or M6-DC40 DC power module from the. The Cisco® ONS M6 Multiservice Transport Platform (MSTP) sets the industry benchmark for compact, easy to operate, fast, and intelligent DWDM solutions. The flexible Cisco ONS M6 platform supports a broad range of solutions, from edge aggregation solutions to metro.
    Release the hinge pins.

    images 15454 m6 dc40 upright

    Connect the power cable to the fuse panel or power source. Rack mounting. In an ANSI rack, the air deflectors are mounted only on the inch rack configuration.

    Table 3. This procedure installs the power modules in the ONS M6 system.

    images 15454 m6 dc40 upright
    Transport america in atlanta georgia
    In an ETSI rack, the shelf can be mounted only in the front position.

    In a multishelf configuration, alarms on the subtended shelves cannot be extended through the node controller. Perform steps 1 to 5 for the active power module installed in slot A.

    Video: 15454 m6 dc40 upright Dyson DC40 - Washing the filters (UK)

    Installing the left vertical air plenum. AC power cable - Japan left exit.

    images 15454 m6 dc40 upright

    Install the ETSI adapter plates on the horizontal air plenums. For Slot A power module, the power cable exits from the left side.

    Choose Connection for Cisco Power Cords.

    Cisco ONS M6 Multiservice Transport Platform Data Sheet Cisco

    Buy a Cisco DC Power Cable for DC40 ETSI Left Exit and get great service and fast delivery. Cisco [M6-DC40=] for $ - Dca Power Module m6dc40 at as of Saturday August 17, Cisco - M6-DC40= - Cisco DCA Power Module - W - 60 V DC. Item #: MFR SKU: M6-DC40= price drop! Lists At: $ You .
    The chassis can be installed with brackets in front position only.

    M6 fan tray assemblies. Install the wing head screws provided with the kit, and tighten to a torque value of The AC power module supports the lamp test procedure and has fans that are directly powered by the module.

    Video: 15454 m6 dc40 upright Dyson DC40 or DC42 - Replacing the cleaner head

    ANSI inch cabinet. Side to Side. Place a mounting bracket flush against the left and right side of the chassis see Diagram 2 of Figure 1.

    images 15454 m6 dc40 upright
    Biomagnification and bioaccumulation difference between medicare
    See Diagram 4 of Figure 1.

    The widest side of the mounting bracket should be towards the front of the shelf. The Electrical Connection Unit ECU, Figure 3 is a narrow, front-facing termination panel for all management, alarm, and multi-shelf connections. M6 AC power module. Contact the appropriate electrical inspection authority or an electrician if you are uncertain that suitable grounding is available. Regulatory Standard Compliance and Agency Approvals. The front-to-top deflector configuration can be operated at a maximum of 50C at m altitude.

    M6-DC Cisco Systems DC power cable for DC40 ETSI right exit 11kVA 63A V 30x C13/6x C19 IEC Input MH Vertical Intl Basic PDU.

    Cisco M6-DCCBL-LE power cable 10 m (DC power cable for ETSI left exit ) DC power cable for DC40 ETSI Left exit . Black power distribution unit [PDU ] (10 WAY VERTICAL PDU WITH 16 AMP - BS COMMANDO PLUG). Cisco M6-DCCBL-LE 10m power cable (DC power cable for ETSI left.

    DC power cable for DC40 ETSI Left exit Prism Enclosures PDU10VAMP 10AC outlet(s) Black power distribution unit (PDU) (10 WAY VERTICAL PDU WITH.
    Verify that the proper fuse and alarm panel has been installed in the top mounting space. Raise the door to slide the pin. Installing the horizontal plenum above the vertical plenums. Align the screw holes on the inch mounting bracket with the screw holes on the left side of the chassis.

    This task verifies the shelf for AC power module installation.

    Insert the screws and tighten them to a torque value of

    images 15454 m6 dc40 upright
    BARVY RAL 7035 MSDS
    The following figure shows the label that is placed on top of ONS M While changing the power modules, ensure that only one power module is replaced at a time and the other power module continues to supply power to the shelf.

    The Cisco ONS M6 has a built-in memory module to back up the software package, IP address, and circuit database, making simplex mode more attractive in cost-sensitive applications. Install the ANSI inch adapter plates on the horizontal air plenums. The intra-building port s of the equipment or subassembly is suitable for connection to intra-building or unexposed wiring or cabling only.

    Measure and cut the cables as needed to reach the ONS M6 from the fuse panel. AC power cable - UK right exit.

    Comments (5)

    1. Mejinn

      Reply

      The inventory details are displayed in the Inventory tab in CTC. Install the vertical air plenum to the left of the horizontal air plenum: Insert the vertical air plenum in the free space between the horizontal air plenum and cabinet.

    2. Kajirr

      Reply

      Ensure that the host is connected to earth ground during normal use. Perform steps 1 to 5 for the active power module installed in slot A.

    3. Tygogis

      Reply

      Figure 8. To insert the AC power module, the screw must be next to the AC silk-screen text; to insert the DC power module the screw must be next to the DC silk-screen text.

    4. Arashirn

      Reply

      Place the left front air deflector flush against the left side of the chassis.